node-red-contrib-google-smarthome

v0.4.14

Published

2 months ago

Lets you control Node-Red via Google Assistant or the Google Home App

Downloads

424

0High
0Medium
0Low

mikejac

caprico85

google smarthome assistant iot node-red

Introduction

A collection of Node-RED nodes to control your smart home devices via Google Assistant or the Google Home app.

This is done by implementing a smart home provider that runs on your own host. So you don't have to rely on any third party services (other than Google) that can go offline, charge you, or leak your data.

What this module does NOT do:

It is not a cloud-hosted solution that you just install and it works. You host a publicly accessible service on your own hardware. It can be difficult to set up. And you do this at your own risk.
It does not talk to your physical devices. It only provides virtual devices in Node-RED. It's up to you to pass commands from the virtual to the physical devices.
It is not an interface to Google devices (like Nest Thermostats, Nest Cams, etc.).
It is for controlling devices only. It does not let you implement your own conversations with Google Assistant.

Prerequisites and Setup Instructions

Follow our setup instructions.

Nodes in this package

General Information

If online is set to false for a node, Google SmartHome will not be able to control the node. It will also show up as offline in the Google Home app.
Nodes will do their best to convert incoming payload data to the required type. For example, you can send a string of ON and it will be converted to true.
Topics must be either as listed below or prepended with one or more /. E.g. my/topic/on. The nodes will only look for the part after the last /, if any.

Google device node

This is a generic node that supports the following Google devices:

Air conditioning unit
Air cooler
Air freshener
Air purifier
Audio-Video receiver
Awning
Bathtub
Bed
Blender
Blinds
Boiler
Camera
Carbon monoxide detector
Charger
Closet
Coffee Maker
Cooktop
Curtain
Dehumidifier
Dehydrator
Dishwasher
Door
Doorbell
Drawer
Dryer
Fan
Faucet
Fireplace
Freezer
Fryer
Garage
Gate
Grill
Heater
Hood
Humidifier
Kettle
Light
Lock
Microwave
Mop
Mower
Multicooker
Network
Outlet
Oven
Pergola
Pet feeder
Pressure cooker
Radiator
Refrigerator
Remote control
Router
Scene
Security system
Sensor
Settop
Shower
Shutter
Smoke detector
Soundbar
Sousvide
Speaker
Sprinkler
Stand mixer
Streaming box
Streaming soundbar
Streaming stick
Switch
Thermostat
Television
Vacuum
Valve
Washer
Water heater
Water purifier
Water softener
Window
Yogurt maker

and the following Google traits:

App selector
Arm/Disarm
Brightness
Camera stream
Channel
Color setting
Color temperature
Cook
Dispense
Dock
Energy storage
Fan speed
Fill
Humidity setting
Input selector
Light effects
Locator
Lock/Unlock
Media state
Modes
Network control
Object detection
On/Off
Open/Close
Reboot
Rotation
Run cycle
Scene
Sensor state
Software update
Start stop
Status report
Temperature control
Temperature Setting
Timer
Toggles
Transport control
Volume

Example flow: See the flow used for the automated tests here

Management

topic can be restart_server, report_state or request_sync.

payload is not used for anything.

restart_server restarts the built-in web server.

report_state will force an update of all states to Google. Mostly useful for debugging.

request_sync will ask Google for a sync to learn about new or changed devices. This is usually done automatically.

The config node

Name: A name for your config node.

Enable Node Debug: If enabled, debug messages will be written to Node-RED's log output.

Default Language: The language of your project.

Local Authentication

Use Google Login: If checked, use Google login authentication.

Login Client ID: If Google Login is enabled, the client ID you received from the Google Sign-In integration.

Authorized emails: If Google Login is enabled, the email addresses authorized to log in.

Username and Password: If Google Login is disabled, a username and password used during account linking in the Google Home app.

Actions on Google Project Settings

Client ID: The client ID you entered in the Actions on Google project.

Client Secret: The client secret you entered in the Actions on Google project.

Google HomeGraph Settings

Jwt Key: Path to the JSON file that you downloaded during setup. Can be an absolute path or a path relative to Node-REDs user dir (where your settings.js, flows.json etc. are stored).

Web Server Settings

Port: TCP port of your choice for incoming connections from Google. Must match what you specified in the Actions on Google project. If empty, it will use the same port as Node-RED.

URL subpath: URL subpath to add to the URL. If set, the URL will change from https://example.com:3001/check to https://example.com:3001/<subpath>/check (resp. /<subpath>/smarthome, /<subpath>/oauth, /<subpath>/token).

Use http Node-RED root path: If enabled, use the same http root path prefix configured for Node-RED, otherwise use /.

Use external SSL offload: If enabled, the smarthome service will use HTTP instead of HTTPS. Check if you want to do SSL termination on a reverse proxy.

Public Key: Full path to the SSL certificate file, e.g. fullchain.pem from Let's Encrypt.

Private Key: Full path to private SSL key file, e.g. privkey.pem from Let's Encrypt.

Note: Certificates are automatically reloaded after renewal. You don't need to restart Node-RED.

Local Fulfillment

Scan Type: The service discovery method to use. Must match what is set in the Actions on Google project.

Discovery Port: A port number to use for UDP or mDNS service discovery.

HTTP Port: A port number to use for the connection from your smart speaker to Node-RED. If empty, it will use the same port as Node-RED. If you are using Node-RED's built-in HTTPS encryption or have a httpAdminRoot set, you need to set a port. Don't create a forwarding rule for this port!

Advanced Settings

Token Duration: The duration of the authorization token used by Google SmartHome to identify itself to the Node-RED SmartHome plugin. Default is 60 minutes.

Report Interval (m): Time in minutes between sending report updates to Google (default is 60 minutes).

Request sync delay (s): Delay in seconds, for requesting devices sync after a deployment. 0 or empty for disable (default is 0).

Set state delay (s): Delay, in seconds, for sending the set_state message after state changes, 0 or empty to disable (default value 0).

Sending spoken notifications

Some devices support sending spoken notifications to your smart speaker. For example, you can play a notification on your speaker when someone rings at the front door or when the washing machine completes a cycle. Unfortunately, you cannot send custom notifications, you can only trigger predefined notifications.

See https://developers.google.com/assistant/smarthome/develop/notifications.

Using the "Google Device" node, create a device with one of the supported traits in Node-RED and deploy it. Currently, only the Object Detection, Run Cycle, and Sensor State traits support notifications.
In the Google Home app, open your new device and enable Spoken Notifications.
To trigger the notification, send a message with a specific payload to the device node. You can find examples for all supported notifications in the examples folder (examples/Spoken%20Notifications). Payloads are documented here.

Inviting other users

You can invite other people into your smart home in the app by following these steps.

Inviting people will not work in all cases. For example, it won't work if either you or the other person has a commercial Google Workspace account. If this is the case, you can share access to your Smart Home project as follows:

If you are currently using username/password authentication, switch to Google Sign-In by following the instructions on Integrating Google Sign-In. Proceed only after you have successfully unlinked and relinked your own account.
In "Authorized emails", add the email address of the account you want to add. Save and deploy.
Open your project in the Google Actions Console.
Select "Manage user access" from the menu (three dots on the top right) choose "Manage user access".
Select "Add".
Enter the email address for the account you want to add. Select at least "Viewer" as the role.
Return to the Google Actions Console. On the Test tab, select Settings and disable On device testing. Then click Start testing.
The person you just added should now able to link to your project by following the steps in Setup Account linking.

Troubleshooting

Some devices can be controlled by voice, but not by the Google Home app. For example windows and sensors. These devices will only show a general page with their room assignments in the app, but they don't show their current state or any buttons to control them. There is nothing we can do about this. This has to be implemented by Google.
Assign your devices to a room. Unassigned devices may experience delayed state updates in the app.
Some errors and possible solutions are listed at Possible errors.
Check Node-Red's debug panel for error messages.
Unlink and relink your account in the Google Home app. Check Node-RED's debug panel for errors while doing so.
If you are having trouble linking your account, try turning off Wi-Fi on your phone to use only the cellular network.
If you are having trouble linking your account, disable "Use Google Login" and try logging in with username/password first. You can switch back to Google Login later.
Restart your flows (using the Restart Flows option in the dropdown menu of the deploy button) while the debug panel is open to see any error messages during initialization.
Go to Actions on Google Console, in tab Test choose logs in Google Cloud.
Check if your service is reachable from the outside. Use reqbin.com or a similar tool to send a GET request to https://example.com:3001/check (with your hostname and port). It should respond with status 200 (OK) and the message "SUCCESS: Smart Home service is reachable!" as one of the first lines. Use https://www.ssllabs.com/ssltest/ to check your SSL certificate.
Check Node-RED's log output. Where you find it depends on how you installed Node-Red. Usually something like journalctl -u nodered, docker logs <container> or a file in /var/log.
Toggle "Enable Node debug" in the configuration node, connect a debug node to the output of the management node and look for debug messages. In the Node-Red UI select 'Restart Flows' on the 'Deploy' button to see messages during initialization.
Go to Actions on Google Console, on tab Test click Reset Test. If this doesn't do anything, click the Settings button, disable and re-enable On device testing.
Check that you have only one single management node and one single config node.
Go through the setup instructions again and compare your settings with what you see on the screenshots

For problems related to local fulfillment, see Troubleshooting local fulfillment.

Contact us

If you have questions, ask them on our Discussions page.
If you think you have found a bug, report it on our Issue Tracker.

Developer resources

Google Smart Home project
Google Smart Home traits list
Actions on Google Console
Google's Smart Home sample project
SYNC Data Validator
Google Home Playground
Similar projects:
- SmartNORA (cloud-hosted Google integration for Node-RED)
- Nabu Casa (Google integration for Home Assistant)
- node-red-contrib-googlehome (Google integration for Node-RED by Ben Hardill)
- Node-RED Smart Home Control (Google integration for Node-RED, based on node-red-contrib-googlehome)

Credits

Parts of this README and much of the code come from Google. In particular, Actions on Google: Smart Home sample using Node.js was of great value.

Published

Vulnerabilities

Links

Maintainers

Keywords

Readme

Table of Contents