ioBroker.cec2

Tests:

Adapter for HDMI CEC

You can monitor / control devices using HDMI CEC. Most modern TVs and multimedia devices support CEC to some extent.

Info

On start this adapter runs cec-client and polls all devices on the HDMI bus. For every CEC device a device in ioBroker is created. The OSDName of a device will become its id in ioBroker (because it should not change and is nicely readable). If devices show up during runtime they will be added to ioBroker, too.

CEC Adresses

Short introduction about CEC addresses, you can skip this, but might want to read here, if you get confused by the description below.

In CEC there are two types of addresses. Both are important.

Logical Address

The logical address is a number between 0 and 15 (or F in Hex which is normally used). The number defines what kind of device it is:

• 0 = TV
• 5 = Audiosystem
• 4,8,11 = Playback
• 1,2,9 = Recording
• 3,6,7,10 = Tuner

The others are reserved (12,13), Freeuse (14) and unregistered/broadcast (15). The devices that use these addresses are restricted in there communication.

The logical address is dynamically assigned. That means on one day you can have the situation that Playback A is assigned address 4 and Playback B 8. But on the next day they are switched on in a different order and then A gets 8 and B 4. (Some devices are always active on the CEC bus though and therefore cling to their addresses). If there are too many devices of one type (i.e. 4 playback devices), then the logical addresses have to be reused and that will happen. The adapter tries to manage this case.

The logical address is used to address messages and reports to. ioBroker needs a logical address, too, in order to receive reports from the bus. Therefore configure the adapter to a device type that you know you have free logical addresses (for example recording).

Physical Address

The physical address is based on the HDMI ports involved for the device. It is basically a path of port numbers towards the device. It is composed from 4 numbers seperated by dots. Some examples:

• 0.0.0.0 = TV
• 1.0.0.0 = 1. HDMI port of the TV
• 2.0.0.0 = 2. HDMI port of the TV
• 2.2.0.0 = 2. HDMI port of the TV, 2. HDMI port of a Switch / AV-Receiver
• 4.1.2.0 = 4. HDMI port of the TV, 1. HDMI port of a AV-Reciever / Switch, 2. HDMI port of the next AV-Receiver/Switch

That should give a basic idea. A 0 means the path is ending.

The physical address is fix for a device unless it is replugged into a different HDMI Port (or any devices before it seen from TV).

States per device

For every device there are the following states created:

• info.active = device was seen recently and logical address should be correct
• info.cecVersion = should be 1.4, determines features
• info.lastSeen = last message from device on CEC bus
• info.logicalAddress = logical address as number
• info.logicalAddressHex = logical address as hex number (needed for own commands)
• info.Name = name the device sets in CEC Bus
• info.physicalAddress = physical address
• info.Vendor = vendor of the device
• activeSource = is the device the active source? Can switch this device to be active source
• menuStatus = lets device be controlled by TV remote
• state = power state of device (lets you switch it on/off, if supported)
• createButtons = press here to generate states for buttons in .buttons subfolder.
• buttons.time = time to press a button for (default 500ms).

Buttons

Button presses do not work for all devices and some might need to have an active connection with the ioBroker device to be controlled via CEC bus. For FireTV it works quite ok. To test button presses, press createButtons button in a device and test some of the created buttons in some situations. Power works for quite a lot devices.

Global States

There are the following global states:

• active-source = physical address of the current active source (can be set to switch inputs)
• arc = Audio Return Channel is (in)active might be able to (de)activate it here
• mute = mute Audiosystem
• raw-command = send commands to cec-client directly (for example 'scan' or tx + CEC Command from http://www.cec-o-matic.com/)
• standbyAll = send all devices to standby
• systemAudio = Audiosystem is/is not in use. Informs devices that they should send volume/mute commands to Audiosystem
• volume = volume of Audiosystem, 0 = mute
• volumeUp/Down = change volume of Audiosystem

Poll States

There is a subfolder "poll" with button-states for most states. If the button is triggered, the adapter will issue a command on CEC Bus to poll the value and set the state accordingly (sadly not all devices react to poll messages, though).

Requirements

cec-client have to be installed. Usually can be installed using:

sudo apt install cec-utils

The user running iobroker (nowadays "iobroker") needs acces to /dev/vchiq. You may need to add the iobroker user to the video group for that:

sudo usermod -a -G video iobroker

Installation

Execute the following command in the iobroker root directory (e.g. in /opt/iobroker)

npm install iobroker.cec2

Or install from admin webpage.

Configuration

• osd name: this name will reported to other devices, for example your TV. You might need to select ioBroker there to receive remote controls in ioBroker.
• device type: You can set the device type, see discussion of logical address above to get an idea what that means. Use a device type that you have not many of.
• prevent unnamed devices: Sometimes devices are not reporting their name in certain situations (for example Nintendo Switch won't report its name when in standby but announce itself). In this situations the adapter might create a duplicate of the device under it's physical address (i.e. for numbers). You can enable this option to prevent it.

Script examples:

See example Scripts for some example scripts that help with / repair multimedia setups.

Changelog

0.1.3 (2024-07-04)

• remove unnecessary files from npm package

0.1.2 (2024-06-04)

• prevent crash
• try restart in case of error with cec-client

0.1.1 (2023-09-06)

• dependency updates.
• sending commands is now more reliable.
• more error handling

0.1.0 (2021-02-18)

• add more translations.
• add more options (poll TV power).

0.0.8 (2021-02-14)

• Switched from unmaintained dependency to own code to control cec-monitor binary.
• Swtiched from event-stream to readline.
• Probably fixed missed incomming events.

License

MIT License

Copyright (c) 2020-2024 Garfonso [email protected]

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.